bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai | bgas training in chennai

BGAS TRAINING

BGAS TRAINING AND CERTIFICATION

 
 

1. BGAS PAINTING INSPECTOR GRADE 3/2

 

Suitable for:

 
Candidates with or without experience in the Painting Inspection Industry. Candidates will be assessed during the course and advised on either grade 3 or 2 exam route dependent on their progress during training.
 

Course Content:

 
Corrosion theory; surface preparation; surface contaminants and tests; paint constituents and technology; solutions and dispersions; drying and curing properties and performance; specified painting conditions; cathodic protection; holiday/pinhole detection; paint-application methods; paint/paint film testing; paint identification; metal coatings; paint faults; colour; inspection methods; specification requirements; health and safety and working practices.
 

Course Objectives:

 
 

Additional Information:

 

Candidates MUST bring:

 
 

NOTE:

 
Renewal can only be made within three months of the expiry date. Any application received after three months of the expiry cannot be considered and can only be renewed by re-examination.

If the applicant is a holder of BGAS Site Coatings Inspector Approval, it should be noted that day 1 of the syllabus will cover items which the applicant may be already conversant in and therefore attendance on this day (although strongly recommended) is entirely at their discretion. Course duration may then be only 4 days. However, should the applicant decide against attendance on this day, there will be no reduction in course fee.

Four day training course with examination on day 5, or for less experienced candidates there is the opportunity to take the examination the following week.
 

ENTRY REQUIREMENTS:

 
No formal entry qualifications required, but a knowledge of dry abrasive blast cleaning or industrial paint application techniques would be advantageous
 

2. BGAS SITE COATING INSPECTOR

 

Suitable for:

 
Candidates with or without previous experience in site coatings inspection wishing to attain BGAS Approval as a Site Coatings Inspector.

Suitable for individuals engaged in the inspection and coating of new and existing pipelines. This approval is very useful to welding inspectors as it can extend their working time capability on pipelines projects.
 

Course Content:

 
Corrosion, specified coating conditions; surface preparation methods and standards; surface contaminants and tests for detection; coating technology; film thickness; coal tar enamels; special situations; hot applied tapes; cold applied laminate tapes; grease based tapes; self-adhesive overwrap tapes; polyethylene cladding; fillers, mastics and putties; heat shrinkable plastics; powder coatings; urethane MCLs; holiday detection; concrete coatings; internal coatings; cathodic protection; stages of pipeline construction; handling, transport and storage; pipeline surveys, health and safety; coating faults; working practices and quality.
 

Course Objectives:

 
 

Additional Information:

 

Candidates MUST bring:

 
 

NOTE:

Renewal can only be made within three months of the expiry date. Any application received after three months of the expiry cannot be considered and can only be renewed by re-examination.

If the applicant is a holder of BGAS Paint Inspector Approval, it should be noted that day 1 of the syllabus will cover items which the applicant may be already conversant in and therefore attendance on these days (although strongly recommended) is entirely at their discretion. Course duration may then be only 4 days. However, should the applicant decide against attendance on this day, there will be no reduction in course fee.

Four day training course with examinations on day 5, or for less experienced candidates there is the opportunity to take the examination the following week.
 

ENTRY REQUIREMENTS:

 
No formal entry qualifications required, but a knowledge of pipeline fabrication techniques, safe working practices, and a general understanding of coating application would be advantageous.